[Exactly as measured] InMode Lifting

First Principle: Honest Energy Delivery During FX & FORMA Treatments

InMode treatments, both FX mode (fat reduction) and FORMA mode (collagen lifting), have a set maximum output. For satisfactory results, it is crucial to use sufficient time and energy.

At our clinic, we adhere to the prescribed treatment time and energy levels. We aim to provide treatments that follow principles for effective results.

At our clinic, all treatments are performed directly by medical staff to enhance safety. Through this, we strive to build trust in the treatment results.

Second Principle: Delicate Approach to Efficiently Increase Temperature During FX Treatment

For effective fat breakdown in FX treatment, maintaining a certain temperature or higher is crucial.

At our clinic, to quickly reach and maintain the target temperature while minimizing pain discomfort,

we perform the treatment by delicately adjusting various factors such as output, suction pressure, treatment speed, sequence, and skin reaction.

During treatment, we utilize the output as much as possible to quickly raise skin temperature through efficient energy delivery.

We apply a longer pulse duration during treatment. By increasing the time high-frequency energy is injected at once, and extending the energy delivery time from the tip, the temperature can be effectively raised.

In addition to the InMode device's real-time temperature check, medical staff directly check the temperature of the treated area with their hands during the procedure. This minimizes discomfort while performing the treatment.

We adjust the treatment speed differently for each area. Initially, we treat the entire skin to ensure even heat distribution, then focus on areas of concern or those with more fat to increase the temperature. This approach reduces discomfort and enhances treatment efficiency, allowing for satisfactory results.

Third Principle: Delicate Treatment Planning Through Personalized Design

Since FX treatment targets the fat layer, carefully designing the individual's skin and fat distribution before the procedure is crucial.

If the treatment proceeds without sufficient consideration, there is a possibility of unwanted hollowing. Therefore, after a detailed consultation with the director to accurately identify areas for asymmetry improvement or concern, the treatment design is determined.

We meticulously analyze the patient's face shape and fat volume to achieve harmonious and natural results.

Fourth Principle: Transparent Process Verification After Treatment

After the treatment, we directly inform the patient about the treatment duration and the amount of energy delivered. This aims to increase trust in the treatment process.

Understanding InMode Treatment at Our Clinic

Radiofrequency (RF) lifting treatments are broadly classified into two methods.

1. Monopolar

This method involves delivering high-frequency energy from a single electrode and recovering the energy through a grounding pad attached to the body.

This method effectively delivers energy to deep skin tissues, resulting in a significant deep heat effect, but sometimes a slight sensation of irritation may be felt.

2. Bipolar

This method involves high-frequency energy circulating between two electrodes, primarily acting on the skin surface and dermis.

This method is relatively less painful and comfortable to receive, but it is characterized by difficulty in delivering energy to deeper fat layers.

*InMode FX, why does it work on the fat layer despite being Bipolar?

As explained earlier, the bipolar method generally struggles to deliver energy to the fat layer.

However, despite being a bipolar system, InMode FX possesses a special structure that allows it to effectively act on the fat layer.

The reason lies in its vacuum suction function.

Through the vacuum suction function, the skin is gently lifted, precisely positioning the skin and subcutaneous fat layer between the two electrodes.

By delivering high-frequency energy in this state, thermal energy can effectively penetrate deep into the fat layer, despite it being a bipolar method.

Through this treatment method, fat cells can be affected by temperatures of approximately 42~45 degrees Celsius,

Damaged fat cells can be naturally expelled from the body through lymphatic circulation. Simultaneously, collagen production can be expected to be stimulated in the dermis layer.

Ultimately, the goal is to achieve both fat reduction and skin elasticity improvement simultaneously.

*Effects of InMode FX

1. Fat Reduction Effect

InMode FX maintains a constant heat of 42~45 degrees Celsius or more for a certain period, inducing damage to the cell membranes of fat cells.

As a result, the contents of damaged fat cells exit the body and are naturally expelled through lymphatic circulation.

Since its primary purpose is fat reduction, its application can be considered for areas with concerning fat accumulation, such as facial jowls or a double chin.

2. Dermal Collagen Production

When thermal stimulation is delivered to the dermis during fat breakdown, fibroblasts are activated, and new collagen begins to form.

Simultaneously, existing collagen fibers contract, allowing you to experience a lifting effect, as if the skin is tightened, immediately after the procedure.

*How InMode Forma works

The Forma treatment focuses on delivering radiofrequency energy to the shallower dermal layer, rather than the fat layer.

As the device is gently moved along the skin surface, it delivers heat between 42 to 43 degrees Celsius.

This temperature can stimulate fibroblasts, helping to improve fine lines, enlarged pores, and reduced skin elasticity.

One of Forma's important features is its ability to maintain a stable temperature throughout the treatment process via a real-time temperature feedback system.

This means collagen production can be promoted at a consistent temperature without excessively heating the skin.

You may feel your skin tightening immediately after the procedure, and collagen regeneration can gradually appear over approximately 2 to 6 weeks.

*FX and Forma: Treatment Area Selection Guide

Sagging or fat concerns in different areas of the face have various underlying causes.

-Double Chin

A double chin typically appears due to excessive accumulation of subcutaneous fat under the chin or weakening of muscles around the jaw.

FX delivers radiofrequency heat to the fat layer in this area, inducing fat cell breakdown and helping to improve skin elasticity under the chin through collagen regeneration.

If the skin is thin and has significantly lost elasticity, Forma treatment can be considered as an adjunctive procedure.

-Jowls (Bulldog Cheeks)

Sagging in this area is a typical mid-face aging phenomenon that occurs as cheek fat shifts downwards with age. FX reduces the amount of unnecessary fat,

and by enhancing elasticity with Forma, you can expect a more refined improvement in your facial contour.

-Cheeks and Side Cheeks

Enlarged pores, fine lines, and rough skin texture are phenomena that occur due to a decrease in collagen density in the dermis.

Forma uses thermal stimulation to activate fibroblasts, inducing collagen and elastin production, which can help improve skin surface density and texture.

-Jawline

When a previously defined jawline becomes less distinct, it is often primarily due to reduced skin elasticity rather than a fat issue. In such cases, targeting the dermis with Forma to induce collagen contraction and regeneration can be effective.

By combining it with FX as needed, you can expect an even clearer improvement in facial contours.

-Sensitive Areas such as Eyes, Forehead, and Mouth

These areas are prone to fine lines and are characterized by thin, sensitive skin.

Forma can provide appropriate stimulation to the dermis even with relatively low output, making it a suitable treatment method for these sensitive areas requiring delicate care.

*The Importance of InMode Treatment

Simply having InMode equipment does not guarantee satisfactory treatment results.

What is important is the combination of handpieces, the depth of heat delivery, sufficient cumulative energy, and delicate customized settings tailored to each skin condition.

For example, in the case of Forma treatment,

Simply delivering a warm sensation to the skin does not actively stimulate collagen production.

In fact, a target temperature of 42 to 43 degrees Celsius must be consistently maintained within the dermis,

and a certain level of cumulative energy must be delivered to each treated area for fibroblasts to be effectively stimulated and produce collagen.

The same applies to FX. Rather than simple radiofrequency irradiation, vacuum suction and thermal energy must be applied together,

and when deep heat of 42 degrees Celsius or higher is sufficiently delivered to the target area for at least 6 minutes, fat breakdown and collagen contraction can be simultaneously induced.

Furthermore, energy exceeding 8-15kJ must be applied depending on the characteristics of each area, and thin skin or areas prone to bruising require careful attention to vacuum pressure adjustment.

Addressing the fat layer first with FX and then performing a finishing lift with Forma can yield more efficient results.

This is because it allows for the control of swelling and thermal reactions that may occur after treatment, while simultaneously delicately refining the skin's lifting lines.

In conclusion,

When it comes to InMode treatment, the role of the practitioner is more crucial than the device itself. Accurate anatomical understanding by experienced medical staff, appropriate adjustment of settings, and personalized design are key factors in achieving good results.

At our clinic, we adhere to the aforementioned principles and continuously research to provide our patients with the most suitable lifting treatments.

When performing InMode treatment, our medical team strives for satisfactory results through a delicate approach and personalized treatment.

Guide to the Treatment Process

Step 1: FX mode utilizes radiofrequency energy and IRE electrical stimulation technology. This stage helps manage unnecessary facial fat by affecting layers from the epidermis to the SMAS, and can contribute to improving facial contours by inducing collagen production.

Step 2: FORMA delivers concentrated thermal energy to the dermis. This can stimulate collagen production, helping with overall wrinkle improvement and enhancing skin elasticity.

All treatment procedures are performed directly by our medical staff.